China SL-FL39 DIN 4102 Smoke Density Fire Tester Manufacturers and Suppliers | Skyline
industrial sewing machine

SL-FL39 DIN 4102 Smoke Density Fire Tester

Kout Deskripsyon:

Apwopriye itilize pou mezire karakteristik la somke-pwodwi nan materyèl bilding anba kontwole kondisyon pou ki degaje konbisyon oswa dekonpozisyon, epi tou li kapab itilize pou lòt plastik.


  • Min.Order Kantite: 1 inite
  • Prix: Negosyab
  • PACKAGE: Plywood Ka
  • Modèl: SL-FL39
  • Standards: ASTM D 2843, DIN 4102
  • pwodwi Detay

    pwodwi baj

    DIN 4102 materyo konstriksyon enflamabilite sonde ekipman / lafimen Dansite dife tèsteur

    Product introduction of the Smoke Density Fire Tester

    Apwopriye itilize pou mezire karakteristik la somke-pwodwi nan materyèl bilding anba kontwole kondisyon pou ki degaje konbisyon oswa dekonpozisyon, epi tou li kapab itilize pou lòt plastik.

    Standards 

    ASTM D 2843, DIN 4102

    Product Specification of the Smoke Density Fire Tester

    Maximum smoke density (MSD) and smoke density (SDR) for the specimen

    0-100% continuously measurable and automatically calculated

    With the standard optical correction error

    not more than 3%; each device is equipped with three standard filters, proof of light source data, representative

    Bunsen lamp working pressure

    (210 ± 5) KPa

    Bunsen lamp on the sample to impose a flame

    4min

    Automatic timing, automatic ignition, automatic smoke; luminous flux can be phased linear calibration test data more acurrate;

    Touch Screen

    5 inch effective display size 11cm wide 6.28cm; b. Resolution: 800 * 480

    communication interface

    RS232, 3.3V CMOS or TTL

    serial port d. storage capacity

    1G

    Gas source

    95% propane gas, or the same purity of the gas (customer-owned)

    dimansyon

    long * wide * high 740 * 500 * high 900 (mm)

     

     

    Fetures:

    a. Size: 5 inch effective display size 11cm wide 6.28cm;

    b. Resolution: 800 * 480

    c. communication interface RS232, 3.3V CMOS or TTL, serial port

    d. storage capacity: 1G

    e. Using pure hardware FPGA driver display, "zero" start time, power can run

    f. using M3 + FPGA architecture, M3 is responsible for instruction resolution, FPGA focus TFT display, speed and reliability are leading the same kind of program

    g. The main controller uses low-power processor, automatically enter the energy-saving mode

    Product parameters of the Smoke Density Fire Tester

     Burning lanp  pou elèv yo limyè, longè 260mm, bouch dyamèt 0.13mm, 45 ° ang ak ti bwat la lafimen;
     photo-électrique sistèm  limyè sous pou lanp lan, pouvwa 15W, opere vòltaj 6V;
     emisyon gaz sistèm  se machin nan ekipe ak yon fanatik fò, apre tès la, tiyo echapman an kapab deyò egzeyate;
     Lafimen seri dansite mezi  0 ~ 100%;
     Lafimen dansite mezi presizyon  ± 3%;
     reseptè  pou selil yo Silisyòm fotovoltaik, limyè pousantaj transmisyon nan 0% pou pasaj la nan limyè, to transmisyon limyè nan 100% limyè san yo pa kouvri konplètman nan;
     Main presyon brûler k ap travay  276KPa (reglabl);

  • Previous:
  • Next:

  • Ekri mesaj ou a isit la epi voye li nan nou
    industrial sewing machine