SL-FL39 DIN 4102 Smoke Density Fire Tester
DIN 4102 ກໍ່ສ້າງວັດສະດຸໄວໄຟອຸປະກອນການທົດສອບ / ຄວັນຢາສູບຫນາແຫນ້ນໄຟ Tester
Product introduction of the Smoke Density Fire Tester
ທີ່ເຫມາະສົມສໍາລັບການນໍາໃຊ້ຂະຫນາດລັກສະນະ somke ການຜະລິດຂອງອຸປະກອນການກໍ່ສ້າງພາຍໃຕ້ສະພາບຄວບຄຸມຂອງການເຜົາໃຫມ້ຫລືສະຫລາຍຕົວ, ແລະຍັງສາມາດໄດ້ຮັບການນໍາໃຊ້ສໍາລັບພລາສຕິກອື່ນໆ.
ມາດຕະຖານ
ASTM D 2843, DIN 4102
Product Specification of the Smoke Density Fire Tester
Maximum smoke density (MSD) and smoke density (SDR) for the specimen |
0-100% continuously measurable and automatically calculated |
With the standard optical correction error |
not more than 3%; each device is equipped with three standard filters, proof of light source data, representative |
Bunsen lamp working pressure |
(210 ± 5) KPa |
Bunsen lamp on the sample to impose a flame |
4min |
Automatic timing, automatic ignition, automatic smoke; luminous flux can be phased linear calibration test data more acurrate;
|
|
Touch Screen |
5 inch effective display size 11cm wide 6.28cm; b. Resolution: 800 * 480 |
communication interface |
RS232, 3.3V CMOS or TTL |
serial port d. storage capacity |
1G |
Gas source |
95% propane gas, or the same purity of the gas (customer-owned) |
ມິຕິ |
long * wide * high 740 * 500 * high 900 (mm) |
Fetures:
a. Size: 5 inch effective display size 11cm wide 6.28cm;
b. Resolution: 800 * 480
c. communication interface RS232, 3.3V CMOS or TTL, serial port
d. storage capacity: 1G
e. Using pure hardware FPGA driver display, "zero" start time, power can run
f. using M3 + FPGA architecture, M3 is responsible for instruction resolution, FPGA focus TFT display, speed and reliability are leading the same kind of program
g. The main controller uses low-power processor, automatically enter the energy-saving mode
Product parameters of the Smoke Density Fire Tester
ໂຄມໄຟເຜົາໄຫມ້ | ສໍາລັບນັກສຶກສາແສງ, ຄວາມຍາວ 260mm, nozzle, ເສັ້ນຜ່າກາງ 013mm, 45 °ມຸມກັບກ່ອງຄວັນຢາສູບ; |
ລະບົບ Photoelectric | ແຫຼ່ງແສງສະຫວ່າງສໍາລັບການ lamp ໄດ້, ພະລັງງານ 15W, ປະຕິບັດການ 6V ແຮງດັນ; |
ລະບົບໄອເສຍ | ເຄື່ອງແມ່ນເຄື່ອງມືຈມີພັດລົມທີ່ເຂັ້ມແຂງ, ຫຼັງຈາກການທົດສອບ, ສະຫາຍສາມາດກໍາກາງແຈ້ງອອກໂຮງຫມໍ; |
ຄວັນຢາສູບລະດັບການວັດແທກຄວາມຫນາແຫນ້ນ | 0 ~ 100%; |
ຄວັນຖືກຕ້ອງວັດແທກຄວາມຫນາແຫນ້ນ | ± 3%; |
ຮັບ | ສໍາລັບຈຸລັງຊິລິຄອນແສງອາທິດ, ອັດຕາການສົ່ງແສງສະຫວ່າງຂອງ 0% ສໍາລັບ passage ຂອງແສງສະຫວ່າງ, ອັດຕາການສົ່ງແສງສະຫວ່າງຂອງແສງສະຫວ່າງ 100% ໂດຍບໍ່ມີການປົກຫຸ້ມຂອງຫມົດໂດຍຜ່ານການ; |
ຫລັກຄວາມກົດດັນ burner ເຮັດວຽກ | 276KPa (ປັບ); |