SL-FL67 Wire and Cable Heat Release Test Device
DIN EN 50399：2017 Wire and Cable Heat Release Test Device with Stainless Steel Two-Way Speed Probe
Pwodwi entwodiksyon nan Fil ak kab Chalè Release Egzamen Aparèy
EN 50399 Espesifik aparèy la ak metòd nan egzamen pou evalyasyon an nan gaye flanm dife vètikal, lage chalè ak pwodiksyon lafimen nan fil vètikal-monte bunched oswa câbles, elektrik oswa optik, nan kondisyon defini. EN 50399 detay aparèy la ak aranjman an ak kalibrasyon nan instrumentation a yo dwe enstale yo nan lòd yo mezire liberasyon an chalè ak pwodiksyon an lafimen pandan tès la dife. pwosedi tès yo dwe itilize pou di ki tès apwobasyon pou klasifikasyon nan câbles nan Euroclasses B1ca, B2ca, CCA ak DCA yo bay yo.
Pwodwi paramèt nan Fil ak kab Chalè Release Egzamen Aparèy
1. Test chamber has the dimension of 1,000±100(W) x 2,000±100(D) x 4,000±100(H) mm. The bottom surface of the test chamber is higher than the ground while the rear side is supplemented with insulated material to insulate it from heat.
2. At the lower section of the test chamber, there is a 800±20(W) x 400±10(D) sized hole at the 150±10mm position from the front side of the chamber to supply the air.
3. There is a 300±30(W)x1,000±100(D) sized exhaust hole at the rear corner of the top section of the test chamber to allow emission of the smoke during the test.
4. A flame trap is installed at the front side of the burner of the vertical flame spread tester to prevent backfire by propane to ensure the utmost safety.
5. Unlike the conventional IEC60332-3 equipment, the vertical flame spread tester records all control and test conditions with the computer to add user friendliness.
6. If stop the excessive combustion test due to Water Spray device installed for extinguish.
7. The program on the requirement on standard and 70,000Btu/h can be program.
8. Wide stainless steel ladder dimensions: 500(W) ×3, 500(H) mm.
9. Standard stainless steel ladder dimensions: 800(W) ×3, 500(H).
10. Two sets of standard propane burner and venturi mixtures.
11. Follow the standard category can program for select a test.
12. Exhaust system consists of smoke collection hood,exhaust duct, air inlet system, Centrifugal fan and frequency converter.
13. The duct section houses all gas sampling probes, temperature and mass flow probes and has ports for the smoke measuring system.
14. Paramagnetic oxygen analyzer, using the method of paramagnetic change to measure the concentration of oxygen in the gas. Concentration range of 0-25%.
15. Carbon Dioxide Analyser (infrared) for use in heat release measurement. Concentration range of 0-10%.
16. Soot filter, cold trap, drying column, pump and waste regulators for conditioning the sample gases prior to analysis.
17. Dataacquisition system and software.
Pwodwi Feature ak Aplikasyon nan Fil ak kab Chalè Release Egzamen Aparèy
1. Standard 19 kabinè inite, ki gen ladan paramayetik O2, ki pa dispèrsif analyser enfrawouj CO2 gaz;
2. Taiwan Advantech done akizisyon tablo 1 seri, ka kolekte tanperati, diferans presyon gaz ak gaz analyser done, elatriye .;
3. en fe de-fason vitès pwofonde, ak yon seri aparèy deteksyon presyon van tankou mikwo Capteur diferans presyon;
4. Etazini OMEGA K-kalite tèrmokapteur 3, detekte tanperati a gaz fwit chemine 1 seri;
5. Ekipe ak yon seri aparèy koleksyon gaz pwofonde, ki konekte ak PTFE tiyo, ka kolekte gaz korozivite;
6. dezumidifikasyon frèt pèlen, gaz fiks koule ak regilatè vòltaj, 1 seri Ameriken aparèy KAS koleksyon gaz ponp, te ekipe ak pur tiyo asye ak PTFE koneksyon kawotchou;
7. An incandescent lamp smoke density measuring system comprising an incandescent light source and a silicon photodiode receiving device;
8. Ekipe ak 5 filtè net, optik seri dansite nan 0.1-2;
9. 4 enpòte aparèy koule mas kontwolè, te ekipe ak presyon diminye tiyo, tiyo Solenoid, elatriye .;
10. Standard lojisyèl tès, ki gen ladan pwosedi kalibrasyon, e yo ka gen pou itilize pou monome tès boule;
11. Ekipe ak 1 seri òdinatè ak aparèy pou enprime aparèy;
12. Tès ekipman tankou tiyo echapman ak santrifujeur fanatik;
13. De contrôleur koule gaz pwopàn mas;
14. De contrôleur koule mas lè;
Ka 15. 22.5KW ak 30KW kalibrasyon flanm dife dwe fèt pa yon kontwolè koule mas aji sou yon brûler sèl;
16. Bundle fil ak aparèy kab tès boule.
Aplikasyon: Sistèm nan tès se yon tès dife medyòm-echèl similye fourni kab oswa fib optik kab. Se kab la tès enstale sou yon nechèl vètikal asye estanda ak deklanche pa yon sous ignisyon espesifye evalye konpòtman ak konbisyon epi ki degaje konbisyon pèfòmans nan nan kab an. Done ki degaje konbisyon pèfòmans pou premye etap yo byen bonè nan yon dife kab,
Egzamen sa a nan to la lage chalè reflete danje a nan flanm dife a gaye ansanm kab la ak enpak la potansyèl de sous nan dife sou zòn nan adjasan. dansite lafimen tès montre yo vizibilite a nan zòn nan dife ak danje a nan lafimen an nan sekirite a pèsonèl.
Pwodwi Detay yo de Fil ak kab Chalè Release Egzamen Aparèy
EN 50399 Tès aparèy se konpoze de IEC 60332-3 aparèy, chalè lage mezi, lafimen mezi dansite ak modifye sistèm Inlet lè. Sa a se akonpli pa Fitting yon ti seksyon enstrumante nan kondui nan sistèm lan tiyo echapman nan mare a ak lè l sèvi avèk sa a ak asosye instrumentation analiz gaz ak lojisyèl. Kay yo seksyon adezif tout gaz echantiyon sond, tanperati ak mas sond koule e li gen pò pou sistèm nan lafimen mezire.
Egzamen sa a ka jwenn karakteristik sa yo nan kab la oswa kab nan kondisyon ki degaje konbisyon sèten:
flanm dife gaye flanm dife gaye FS
Chalè Release To Chalè Release To HRR
Total lage chalè Total Chalè Release THR
lafimen to pwodiksyon lafimen Pwodiksyon To SPR
Total lafimen pwodiksyon Total lafimen Pwodiksyon ti kiyè
Burning Kwasans Index To dife Kwasans To FIGRA
|
Standards |
DIN : DIN EN 50399: 2017; EN : EN 50399; GB/T 31248: 2014 |
|
dimansyon |
1120 mm (W) x 2200 mm (D) x 5600 mm (H) |
|
Pwa |
1200kg |
|
Elektrik |
110V AC 60Hz / 230V AC 50Hz, 5A |
|
Anbyen Tanperati |
Opere 10 ° C rive nan 35 ° C |
|
Gas |
air and propane |
