China SL-FL67 Wire and Cable Heat Release Test Device Manufacturers and Suppliers | Skyline
industrial sewing machine

SL-FL67 Wire and Cable Heat Release Test Device

አጭር መግለጫ:

EN 50399 specifies the apparatus and methods of test for the assessment of vertical flame spread, heat release and smoke production of vertically-mounted bunched wires or cables, electrical or optical, under defined conditions.


  • Min.Order ብዛት: 1 አሃድ
  • ዋጋ: በስምምነት
  • ጥቅል: ኮምፖንሳቶ መያዣ
  • Model: SL-FL67
  • መስፈርቶች: DIN EN 50399:2017,EN 50399
  • የምርት ዝርዝር

    የምርት መለያዎች

    DIN EN 50399:2017 Wire and Cable Heat Release Test Device with Stainless Steel Two-Way Speed Probe

    ወደ ምርት መግቢያ  በባንክ ሒሳብ እና የኬብል ሙቀት የተለቀቀበት ሙከራ መሣሪያ

    EN 50399 ይገልጻል ወደ መቅላጠፊያ መሳሪያ እና ቋሚ ነበልባል መስፋፋት, ሙቀት ልቀት እና የተገለጹ ሁኔታዎች ስር የኤሌክትሪክ ወይም የጨረር በቁሙ-ሰክቷል bunched ገመዶች ወይም ገመዶች, ስለ ጢስ ምርት ግምገማ ፈተና ዘዴዎች. EN 50399 ወደ መቅላጠፊያ መሳሪያ እና instrumentation ያለውን ዝግጅት እና የካሊብሬሽን እሳት ፈተና ወቅት ሙቀት መለቀቅ እና ጭስ ምርት ለመለካት ቅደም እንዲጫን ዝርዝር. የሙከራ ሂደቶች Euroclasses B1ca, B2ca, Cca እና Dca ውስጥ ኬብሎች የሚመደቡበት አይነት ተቀባይነት ለሙከራ ጥቅም ላይ የሚውሉ ይሆናል ተሰጥተዋል.

    ወደ ምርት መለኪያዎች  በባንክ ሒሳብ እና የኬብል ሙቀት የተለቀቀበት ሙከራ መሣሪያ

    1. Test chamber has the dimension of 1,000±100(W) x 2,000±100(D) x 4,000±100(H) mm. The bottom surface of the test chamber is higher than the ground while the rear side is supplemented with insulated material to insulate it from heat.
    2. At the lower section of the test chamber, there is a 800±20(W) x 400±10(D) sized hole at the 150±10mm position from the front side of the chamber to supply the air.
    3. There is a 300±30(W)x1,000±100(D) sized exhaust hole at the rear corner of the top section of the test chamber to allow emission of the smoke during the test.
    4. A flame trap is installed at the front side of the burner of the vertical flame spread tester to prevent backfire by propane to ensure the utmost safety.
    5. Unlike the conventional IEC60332-3 equipment, the vertical flame spread tester records all control and test conditions with the computer to add user friendliness.
    6. If stop the excessive combustion test due to Water Spray device installed for extinguish.
    7. The program on the requirement on standard and 70,000Btu/h can be program.
    8. Wide stainless steel ladder dimensions: 500(W) ×3, 500(H) mm.
    9. Standard stainless steel ladder dimensions: 800(W) ×3, 500(H).
    10. Two sets of standard propane burner and venturi mixtures.
    11. Follow the standard category can program for select a test.
    12. Exhaust system consists of smoke collection hood,exhaust duct, air inlet system, Centrifugal fan and frequency converter.
    13. The duct section houses all gas sampling probes, temperature and mass flow probes and has ports for the smoke measuring system.
    14. Paramagnetic oxygen analyzer, using the method of paramagnetic change to measure the concentration of oxygen in the gas. Concentration range of 0-25%.
    15. Carbon Dioxide Analyser (infrared) for use in heat release measurement. Concentration range of 0-10%.
    16. Soot filter, cold trap, drying column, pump and waste regulators for conditioning the sample gases prior to analysis.
    17. Dataacquisition system and software.

    የምርት የባህሪ እና መካከል ማመልከቻ  በባንክ ሒሳብ እና የኬብል ሙቀት የተለቀቀበት ሙከራ መሣሪያ

    1. መደበኛ paramagnetic O2, ያልሆኑ dispersive ኢንፍራሬድ CO2 ጋዝ analyzer ጨምሮ 19 ካቢኔ አሃድ;
    2. ታይዋን Advantech ውሂብ ማግኛ ቦርድ 1 ስብስብ, ወዘተ ሙቀት, ጋዝ ግፊት ልዩነት እና ጋዝ analyzer ውሂብ መሰብሰብ ይችላል .;
    እንዲህ ያሉ የማይክሮ ልዩነት ግፊት ዳሳሽ እንደ ነፋስ ግፊት ማወቂያ መሳሪያዎች ስብስብ ጋር 3. የማይዝግ የብረት በሁለት መንገድ ፍጥነት መጠይቅን;
    የ flue ጋዝ ሙቀት 1 ስብስብ ማግኘት እየከበደን 4. ዩናይትድ ስቴትስ ኦሜጋ K-ዓይነት thermocouple 3;
    PTFE ከቧንቧ እንደተገናኘ ጋዝ ክምችት መጠይቅን መሣሪያ ስብስብ, በመታጠቅ 5., ማጉረምረም ጋዝ መሰብሰብ ይችላል;
    6. Dehumidifying ቀዝቃዛ ወጥመድ, ከማይዝግ ብረት ቧንቧ እና PTFE ቱቦ ግንኙነት ጋር የተገጠመላቸው ጋዝ ቋሚ ፍሰት እና ቮልቴጅ ትቆጣጠራለች, የአሜሪካ CAST ጋዝ ክምችት ፓምፕ መሣሪያ 1 ስብስብ;
    7. An incandescent lamp smoke density measuring system comprising an incandescent light source and a silicon photodiode receiving device;
    8. 5 ገለልተኛ ማጣሪያዎች, 0.1-2 መካከል የጨረር መጠጋጋት ክልል በመታጠቅ;
    9. 4 ከውጪ ጅምላ ፍሰት መቆጣጠሪያ መሣሪያዎች, ወዘተ ግፊት በመቀነስ ቫልቮች, solenoid ቫልቮች, የተገጠመላቸው .;
    የካሊብሬሽን ሂደቶች ጨምሮ, እና monomer የሚነድ ፈተና ላይ ሊውል ይችላል 10. መደበኛ ፈተና ሶፍትዌር;
    11. ኮምፒውተር እና የአታሚ መሣሪያዎች 1 ስብስብ በመታጠቅ;
    እንደ አደከመ ፒፓ እና ሴንትሪፉጋል አድናቂ እንደ 12. ሙከራ መሣሪያዎች;
    13. ሁለት ፕሮፔን የጅምላ ፍሰት መቆጣጠሪያዎች;
    14. ሁለት አየር የጅምላ ፍሰት መቆጣጠሪያዎች;
    15. 22.5KW እና 30KW ነበልባል መለካት በአንድ በርነር ላይ እርምጃ አንድ የጅምላ ፍሰት መቆጣጠሪያ በማድረግ ሊከናወን ይችላል;
    16. ጥቅል ሽቦ እና የኬብል የሚነድ የሙከራ መሣሪያ.

    መተግበሪያ: ይህ ፈተና ስርዓት ይጠቀለላሉ የኬብል ወይም ፋይበር ኦፕቲክ ገመድ simulating አንድ መካከለኛ-ልኬት እሳት ፈተና ነው. የሙከራ ገመድ አንድ ቋሚ መደበኛ ብረት መሰላል ላይ የተጫኑ እና ገመድ ውስጥ ለቃጠሎ ባህሪ እና ለቃጠሎ አፈጻጸም ለመገምገም በተወሰነ መለኰስ ምንጭ መቀስቀስ ነው. አንድ ገመድ የእሳት መጀመሪያ ደረጃ ለ ለቃጠሎ አፈጻጸም ውሂብ,

    ሙቀት መለቀቅ መጠን ያለው ፈተና ገመድ እና ከጎን አካባቢ ላይ እሳት ምንጭ ያለውን እምቅ ተፅዕኖ አብሮ በማስፋፋት ነበልባል ያለውን አደጋ ያንጸባርቃል. ጢስ ጥግግት ፈተና ትዕይንቶች እሳት አካባቢ ታይነት እና የግል ደህንነት ጢስ ያለውን አደጋ.

    ወደ ምርት ዝርዝር በባንክ ሒሳብ እና የኬብል ሙቀት የተለቀቀበት ሙከራ መሣሪያ

    EN 50399 የሙከራ ዕቃ ይጠቀማሉ IEC 60332-3 ዕቃ ይጠቀማሉ, ሙቀት መለቀቅ የመለኪያ, ጭስ ጥግግት የመለኪያ እና ሊቀየር የአየር መፍሰሻ ሥርዓት የያዘ ነው. ይህ ሳይጨርሱ ያለውን አደከመ ሥርዓት ወደ ducting እና ተያያዥ ጋዝ ትንተና instrumentation እና ሶፍትዌር ጋር ይህን በመጠቀም አነስተኛ instrumented ክፍል ይገባናልና በማድረግ ማከናወን ነው. የ ቱቦ ክፍል ቤቶች ለመፈልሰፍ, የሙቀት እና ጅምላ ፍሰት ለመፈልሰፍ እና ጭስ የመለኪያ ሥርዓት ወደቦች አሉት ወሳደድ ሁሉ ጋዝ.
    ወደ ፈተና አንዳንድ ለቃጠሎ ሁኔታዎች ስር ኬብል ወይም ኬብል የሚከተሉትን ባህሪያት ሊያገኙ ይችላሉ:
    ነበልባል ስርጭት ነበልባል መስፋፋት FS
    ሙቀት የተለቀቀው ተመን ሙቀት የተለቀቀው ተመን HRR
    ጠቅላላ ሙቀት የተለቀቀ ጠቅላላ ሙቀት የተለቀቀው THR
    ጭስ ምርት መጠን ጭስ ምርት ተመን SPR
    ጠቅላላ ጢስ ምርት ጠቅላላ የምርት TSP ጭስ
    እድገት ደረጃ ጠቋሚ እሳት እድገት ደረጃ FIGRA የሚነድ

    መስፈርቶች

    ዲአይኤን: DIN EN 50399: 2017; EN : EN 50399; GB/T 31248: 2014

    ስፉት

    1120 mm (W) x 2200 mm (D) x 5600 mm (H)

    ሚዛን

    1200kg

    የኤሌክትሪክ

    110V AC 60Hz / 230V AC 50Hz, 5A

    የአካባቢ ሙቀት

    35 ወደ 10 ° C ኦፐሬቲንግ ° ሴ

    Gas

    air and propane


  • የቀድሞው:
  • ቀጣይ:

  • እዚህ መልዕክት ይጻፉ እና ለእኛ ይላኩት
    industrial sewing machine