จีน OSU ความร้อนที่วางจำหน่ายอัตรา Tester ผลิตและผู้จำหน่าย | Skyline

OSU ความร้อนที่วางจำหน่ายอัตรา Tester

คำอธิบายสั้น:

ทดสอบ OSU ความร้อนอัตราการปลดปล่อยได้รับการอนุมัติโดยจอห์นฟาของการบริหารการบินแห่งชาติของประเทศสหรัฐอเมริกาได้รับการออกแบบมาโดยสมิ ธ จากมหาวิทยาลัยแห่งรัฐโอไฮโอในปี 1972 และต่อมาได้กลายเป็นเครื่องมือที่ใช้ในการทดสอบการเผาไหม้ที่จอห์นฟากำหนดสำหรับการทดสอบอัตราการปล่อยความร้อนของวัสดุเกี่ยวกับการบิน


  • Min.Order จำนวน: 1 หน่วย
  • ราคา: ต่อรองได้
  • แพคเกจ: ไม้อัดกรณี
  • รุ่นSL833
  • มาตรฐาน: AITM 2.0006, BSS 7322, FAR PART 25 ภาคผนวก F Part IV
  • รายละเอียดผลิตภัณฑ์

    Tags สินค้า

    OSU Heat Release Rate Tester Stainless Steel Combustion Test Chamber Equipped

    ข้อมูลผลิตภัณฑ์ ของ OSU hHeat Release อัตรา Tester

    The OSU heat release rate tester approved by FAA of the Federal Aviation Administration of the United States was originally designed by Smith of Ohio State University in 1972, and later became a FAA designated combustion test instrument for testing the heat release rate of Aeronautical materials. The test standards are FAR Part 25 Appendix F Part IV, Airbus AITM 2.00. 06, Boeing BSS 7322.

    ลักษณะการทำงานของ OSU ความร้อนที่วางจำหน่ายอัตรา Tester

    1. Stainless steel combustion test chamber with high temperature glass observation window;
    2. The heat radiation source is 4 Glowbars heating rods, which can provide 35KW/M2 heat radiation flux.
    3. Two independent PID temperature controllers are used for heating temperature control.
    4. Equipped with fully automatic pneumatic sample propulsion device and shielding door device;
    5. Equipped with upper burner and movable lower burner;
    6. Rotor flowmeter can be used to adjust the gas flow rate of upper and lower burners.
    7. Equipped with movable T-type calibration burner device and flow controller;
    8. Mass flow controller is applied to thermopile temperature calibration automatically.
    9. Water-cooled heat flow meter is equipped with cooling mode to measure the heat radiation flux of the fire surface.
    10. The air temperature control device can provide constant temperature and flow air for the test chamber.
    11. The orifice flowmeter is used to measure the flow pressure entering the test bin.
    12. Equipped with data acquisition system and heat release standard test software.

    สินค้า พารามิเตอร์ of OSU Heat Release Rate Tester

     ขนาด  760mm (กว้าง) x 1850mm x (H) x 850mm (D)
     น้ำหนัก  218KG
     ความต้องการไฟฟ้า  220 โวลต์ 35 แอมป์
     อุณหภูมิโดยรอบ  10 ℃ถึง 35 ℃
     เสริมแก๊ส  อุณหภูมิคงที่และคงแก๊สปัจจุบัน
     การเผาไหม้ก๊าซ  มีเทน
     มาตรฐาน   AITM 2.0006, BSS 7322, FAR PART 25 ภาคผนวก F Part IV
     การประยุกต์ใช้งาน  วัสดุการบิน

     


  • ก่อนหน้านี้:
  • ถัดไป:

  • เขียนข้อความของคุณที่นี่และส่งมาให้เรา