Хятад улс OSU Дулаан гаргах түвшин шалгагч үйлдвэрлэгчид болон нийлүүлэгчид | Skyline

OSU Дулаан гаргах түвшин шалгагч

Товч тодорхойлолт:

АНУ-ын Холбооны нисэхийн удирдлагын FAA баталсан OSU дулаан гаргах түвшин шалгагч нь анх 1972 онд Ohio State их сургуулийн Смит бүтээсэн, дараа нь нисэхийн материалын дулаан гаргах хурдыг шалгах нь FAA томилогдсон шаталтын туршилтын багаж болсон байна.


  • Min.Order Тоо ширхэг: 1 нэгж
  • Үнэ: тохиролцох
  • Багц: фанер хэрэг
  • Загвар: SL833
  • Стандарт: AITM 2,0006, BSS 7322, FAR ХЭСЭГ 25 ХАВСРАЛТ оны IV-р хэсэг
  • Бүтээгдэхүүний дэлгэрэнгүй

    Бүтээгдэхүүний хаягууд

    OSU Heat Release Rate Tester Stainless Steel Combustion Test Chamber Equipped

    Бүтээгдэхүүний мэдээлэл  OSU hHeat гаргах түвшин шалгагч

    The OSU heat release rate tester approved by FAA of the Federal Aviation Administration of the United States was originally designed by Smith of Ohio State University in 1972, and later became a FAA designated combustion test instrument for testing the heat release rate of Aeronautical materials. The test standards are FAR Part 25 Appendix F Part IV, Airbus AITM 2.00. 06, Boeing BSS 7322.

    OSU Дулаан гаргах түвшин шалгагч Гүйцэтгэлийн шинж чанар

    1. Stainless steel combustion test chamber with high temperature glass observation window;
    2. The heat radiation source is 4 Glowbars heating rods, which can provide 35KW/M2 heat radiation flux.
    3. Two independent PID temperature controllers are used for heating temperature control.
    4. Equipped with fully automatic pneumatic sample propulsion device and shielding door device;
    5. Equipped with upper burner and movable lower burner;
    6. Rotor flowmeter can be used to adjust the gas flow rate of upper and lower burners.
    7. Equipped with movable T-type calibration burner device and flow controller;
    8. Mass flow controller is applied to thermopile temperature calibration automatically.
    9. Water-cooled heat flow meter is equipped with cooling mode to measure the heat radiation flux of the fire surface.
    10. The air temperature control device can provide constant temperature and flow air for the test chamber.
    11. The orifice flowmeter is used to measure the flow pressure entering the test bin.
    12. Equipped with data acquisition system and heat release standard test software.

    Бүтээгдэхүүний  параметрүүд of OSU Heat Release Rate Tester

     Хэмжээ  760mm (W) х 1850mm X (H) х 850mm (D)
     Жин  218KG
     Цахилгаан шаардлага  220 V, 35 Amps
     Орчны температур  10 ℃ 35 ℃
     Туслах хийн  Тогтмол Температур болон тогтмол одоогийн хийн
     шаталтын хийн  метан
     Стандарт   AITM 2,0006, BSS 7322, FAR ХЭСЭГ 25 ХАВСРАЛТ оны IV-р хэсэг
     Програм  нисэхийн материал

     


  • Өмнөх:
  • Дараа нь:

  • Энд таны захиасыг бичиж, бидэнд илгээнэ