Қытай OSU жылу бөле Rate Tester өндірушілер мен жеткізушілердің | Skyline

OSU жылу бөле Rate Tester

Қысқаша сипаттамасы:

АҚШ Федералдық авиация әкімшілігінің FAA бекіткен OSU жылу босату жылдамдығы сынақшы бастапқыда 1972 жылы Огайо мемлекеттік университетінің Смит әзірленген, ал кейінірек аэронавигациялық материалдардың жылу босату жылдамдығы тестілеу үшін FAA тағайындалған жану сынақ құрал болды.


  • Min.order саны: 1 бірлік
  • Бағасы: Келісімді
  • Пакет: фанера Case
  • Үлгі: SL833
  • Стандарттар: AITM 2,0006, BSS 7322, FAR бөлігі 25 ҚОСЫМША F IV бөлім
  • Бөлшекті өнім

    Өнім Тегтер

    OSU Heat Release Rate Tester Stainless Steel Combustion Test Chamber Equipped

    Өнім туралы ақпарат  OSU hHeat босату жылдамдығы тестерлері

    The OSU heat release rate tester approved by FAA of the Federal Aviation Administration of the United States was originally designed by Smith of Ohio State University in 1972, and later became a FAA designated combustion test instrument for testing the heat release rate of Aeronautical materials. The test standards are FAR Part 25 Appendix F Part IV, Airbus AITM 2.00. 06, Boeing BSS 7322.

    OSU жылу бөлінудің Rate тестерлері сипаттамалары

    1. Stainless steel combustion test chamber with high temperature glass observation window;
    2. The heat radiation source is 4 Glowbars heating rods, which can provide 35KW/M2 heat radiation flux.
    3. Two independent PID temperature controllers are used for heating temperature control.
    4. Equipped with fully automatic pneumatic sample propulsion device and shielding door device;
    5. Equipped with upper burner and movable lower burner;
    6. Rotor flowmeter can be used to adjust the gas flow rate of upper and lower burners.
    7. Equipped with movable T-type calibration burner device and flow controller;
    8. Mass flow controller is applied to thermopile temperature calibration automatically.
    9. Water-cooled heat flow meter is equipped with cooling mode to measure the heat radiation flux of the fire surface.
    10. The air temperature control device can provide constant temperature and flow air for the test chamber.
    11. The orifice flowmeter is used to measure the flow pressure entering the test bin.
    12. Equipped with data acquisition system and heat release standard test software.

    Өнім  параметрлері of OSU Heat Release Rate Tester

     Өлшем  760mm (W) х 1850mm х (H) х 850 мм (D)
     салмақ  218KG
     Электр талаптары  220 В, 35 ампер
     Қоршаған ортаның температурасы  10 ℃ 35 ℃
     көмекші газ  Тұрақты температурада және тұрақты Ағымдағы газ
     жану газ  метан
     стандартты   AITM 2,0006, BSS 7322, FAR бөлігі 25 ҚОСЫМША F IV бөлім
     Өтініштер  авиация материалдар

     


  • Алдыңғы:
  • Келесі:

  • хабарламаңызды жазыңыз және бізге жіберіңіз