Lachin materyo pou konstriksyon enflamabilite tèsteur Konpayi fabrikasyon yo ak Founisè | Skyline

Materyo pou konstriksyon enflamabilite tèsteur

Kout Deskripsyon:

Estanda a se yon referans a ISO 9705 " sifas materyèl plen gwosè tès la chanm " writing standard of combustion test, the test method to simulate the corner fire scenario as a condition of standard test, and test the installation of the sample completely according to actual use, which is one of the most reliable standard test method.


  • Min.Order Kantite: 1 inite
  • Prix: Negosyab
  • PACKAGE: Plywood Ka
  • Modèl: SL-FL1583
  • Creole: ISO 9705:2016
  • pwodwi Detay

    pwodwi baj

    ISO 9705Building Materials Flammability Tester Fire Tests — Full - Scale Room Test For Surface Products

    Pwodwi entwodiksyon  nan  yo  egzamen Full - Echèl Sal Egzamen Pou Sifas pwodwi yo

    Based on Oxygen Consumption Principle GB/T 25207-2010 《Fire tests-Full-scale room tester for surface products》.The standard is a reference to ISO 9705《the surface material full size room test 》writing standard of combustion test, the test method to simulate the corner fire scenario as a condition of standard test, and test the installation of the sample completely according to actual use, which is one of the most reliable standard test method.Due to the relatively complex sample quantity and test conditions required by this test, it is usually used in fire science research and to evaluate the combustion characteristics of materials that cannot be correctly evaluated by small size test.
    The test device consists of four parts, including combustion chamber, flue gas collection and sampling system, gas analysis and data processing system and gas supply system. The test was carried out in a combustion chamber with a sample surface area of about 21 m2 and the door was normally open. The tested materials were installed according to the actual use. A rectangular triangular sand box burner with propane gas was installed at the corner of the inner wall of the room. During the test, the flow rate of gas should be controlled to make the standard heat output of the fire source 100 kW before 10 minutes. When the material did not explode, the flow rate of gas should be adjusted to increase the heat output to 300 kW and last 10 minutes. During a total 20-minute test period, the test can be stopped if there is flashover. The determination of explosive phenomena can be judged by observing and testing curves of heat release rate. 
    During the test, the total heat release, heat release rate, flue gas generation and flue gas generation rate were tested.

    Karakteristik Pwodwi Pèfòmans nan egzamen Full - Echèl Sal Egzamen Pou Sifas pwodwi yo

    1.Full seri ekipman an gen ladan chanm ki degaje konbisyon, koleksyon gaz fwit chemine ak echantiyon sistèm, analiz gaz ak done sistèm ak sistèm ekipman pou gaz pwosesis.
    2. se konik Pèseptè a fwit chemine gaz enstale dirèkteman anwo platfòm la peze ak echantiyon an. Dimansyon anba la se 3000mm X 3000mm ak wotè a se 1000mm. Tèt la nan konik pèseptè a gaz fwit chemine se 900mm X 900mm X 900mm kare. An menm tan an, de plak X 900mm asye 500 mm yo enstale nan kare nan tèt yo fòme yon Homogenizer gaz fwit chemine.
    3. Longè a pi kout la nan pur tiyo echapman lafimen asye se pa mwens pase 5000mm ak dyamèt li se 400 mm. Lafimen melanje aparèy yo enstale nan de bout.
    4. Sistèm nan tiyo echapman gen ase kapasite nan kolekte tout gaz la fwit chemine ki te pwodwi pa tès ki degaje konbisyon. Ka Volim nan tiyo echapman nan fanatik la ap kontinyèlman ajiste, ak pousantaj la tiyo echapman se pa mwens pase 3.5m / s.
    5. fanatik sou lafimen echapman se santrifujeur fanatik, revètman anndan an se asye pur, rezistans a tanperati se pa mwens pase 300 degre, epi li se vitès la ajiste pa fanatik frekans konvèsyon.
    6. Ranje a mezire nan aparèy la peze se 0-5KG, ak presizyon nan se pa mwens pase 0.1g.
    Se 7. Zòn nan mezi complète ekipe ak pwofonde presyon, twa tèrmokoupl, pwofonde pran echantiyon gaz ak sistèm mezi dansite lafimen.
    Se 8. sandboks brûler ki te ranpli avèk gravye ak 4mm-8mm gwosè patikil ak sab ak gwosè 2mm-3mm patikil. Kouch nan tèt nan sab anwo se nivo anpil ladan yo anwo nan brûler.
    Se 9. Sifas ignisyon adopte pou ignisyon nan brûler bwat sab, ak ba to siksè ignisyon tankou etensèl ignisyon pa itilize.
    10. Ekipe ak iltravyolèt flanm dife kontwòl ak D 'Équipement pwoteksyon nan asire sekirite a nan sistèm lan;
    11. Mass koule kontwolè ak pòte nan 0 g / s-7 g / s, li presizyon pa pi piti pase 1.5%, maksimòm pouvwa pwodiksyon nan 300 KW;
    12. Sistèm nan fwit chemine pran echantiyon gaz, ki gen ladann nan sann filtre, COMPRESSOR refrijeran, kolòn siye, echantiyon ponp ak koule mèt, ta dwe kapab echantiyon gaz efektivman kolekte fwit chemine ak absòbe gaz la tiyo echapman.
    13. Enpòte manbràn ponp, echantiyon koule pa pi piti pase 13L / min;
    Se 14. Tèt la filtre nan enpòte lafimen ak pousyè filtre ki konpoze de PTFE solid ak fib 0.5um vè filtre andedan materyèl.
    15. Compression refrijeran, kapasite refwadisman 320KJ / h, lawouze pwen estabilite 0.1 degre, lawouze pwen estatik chanjman 0.1K, refwadisman koule pa pi piti pase 6L / min;
    16. Enpòte rotor debimètr, mezire ranje se 0-5L / min;
    17. Aparèy la mezire konplè gen ladan twa tèrmokoupl OMEGA enpòte ki gen kontak yo ta dwe chita sou yon arc ak ak yon reyon (87 + 5) mm soti nan aks la, ak ang ki genyen ant yo se 120 degre.
    Se 18. pwofonde nan jounal-bidirectionnelle ki konekte nan yon Capteur presyon enpòte ak yon seri mezire nan omwen (0-200) PA ak yon presizyon nan <2 PA. Lè a repons nan 90% pwodiksyon nan Capteur presyon se 1 a nan pi .
    19. analyser la oksijèn yo ta dwe paramayetik epi yo dwe kapab mezire omwen 02 ak yon konsantrasyon nan 16% -21% (V / V). Lè a repons nan analyser la oksijèn pa ta dwe depase 12 segonn. Flote a ak bri nan analyser la pa ta dwe depase 100 x 10-6 nan 30 minit. Pwodiksyon an nan sistèm nan done akizisyon ta dwe gen yon rezolisyon maksimòm de 100 x 10-6.
    20. Gaz kabonik analyser ta dwe IR kalite epi yo dwe kapab mezire omwen 0% - 10% konsantrasyon CO2. Linear la nan analyser la yo ta dwe omwen 1% nan seri a plen. Lè a repons nan analyser la pa ta dwe depase 12 segonn.
    Se 21. lafimen sistèm dansite mezi enstale sou tiyo a bò nan tiyo a tiyo echapman ak jwenti fleksib. Se lanp lan enkandesan itilize nan (2900 +100) tanperati koulè K.
    22. eleman mezire Optical, mezire ranje se 400-750 NM limyè vizib, transmissions presizyon se 0.01%.
    23. 100% ak 0% mòd yo kalibrasyon nan eleman optik mezi yo se: se zewo kalibrasyon pwen konplete pa sinon koupe enkandesan sous limyè ak lojisyèl klike sou 0%; 100% kalibrasyon ranpli pa klike sou 100% san yo pa okluzyon nan chemen limyè, epi li se pa gen okenn filtre net itilize nan anfòm done chemen optik;
    24. Aparèy la pou mezire anbyen atmosferik, presyon gen yon presizyon nan ± 200 PA.
    25. akizisyon nan done ak sistèm analiz asire presizyon nan ak disponiblite nan akizisyon done ak anrejistreman an otomatik nan done yo mande yo chak 3 segonn. Kalkil la nan done lojisyèl se kòrèk epi yo rezilta yo ap efikas. Epi yo ka bay kalibrasyon ak operasyon koòdone ki anba la a;
    26.O 2 / CO 2 analyser kalibrasyon: O 2 / CO 2 pwodiksyon bri ak drift kalibrasyon; ak rezilta nan fòm pwodiksyon;
    27. Lojisyèl an gen ladan optik sistèm kalibrasyon, bri ak drift kalibrasyon nan fwit chemine sistèm mezi gaz ak fòm pwodiksyon nan rezilta yo.
    28. Lojisyèl an gen ladan optik sistèm kalibrasyon, filtre kalibrasyon ak fòm pwodiksyon rezilta.
    29. Lojisyèl an gen ladan volim lè kalibrasyon, volim lè kontwòl seri kalibrasyon ak fòm pwodiksyon rezilta.
    30. Lojisyèl an gen ladan kalibrasyon etap ak fòm pwodiksyon rezilta.
    31. Lojisyèl an gen ladan pwosedi a tès yo ak fòm nan pwodiksyon nan rezilta yo.
    32. Ekipe ak òdinatè ak aparèy pou enprime sistèm.

    Pwodwi  paramèt  nan  egzamen Full - Echèl Sal Egzamen Pou Sifas pwodwi yo
    Applications: building materials, shipping materials
    Standards: DS/ISO/TR 9705-2, ISO 9705:2016
    Size: Combustor Size: 2.4M (L) X 3.6M (H) X 2.4M (W)
    Weight: 700KG
    Smoke hood size: 3M (W) X 3M (D) X 1M (H)
    Installation requirements: Electricity requirements: 220V, 10A; 380V, 5KW
    Ambient temperature: 10 ℃ to 35 ℃
    Gas Requirements: Propane Gas Calibration Gas: N2, CO2 Standard Gas


  • Previous:
  • Next:

  • Ekri mesaj ou a isit la epi voye li nan nou