Tuam Tshoj OSU Thaum tshav kub kub Tso Rate Tester Manufacturers thiab lwm tus | skyline

OSU Thaum tshav kub kub Tso Rate Tester

Luv hauj lwm:

Lub OSU tshav kub tso tawm tus nqi tester pom zoo los ntawm FAA ntawm Tsoom Fwv Teb Chaws chaw ua dav hlua Administration ntawm lub tebchaws United States yog Ameslikas tsim los ntawm Smith ntawm Ohio State University nyob rau hauv 1972, thiab tom qab ntawd los ua ib tug FAA xws combustion xeem ntsuas rau kev soj ntsuam lub tshav kub tso tawm tus nqi ntawm Aeronautical cov ntaub ntawv.


  • Min.Order Quantity: 1 unit
  • Nqe: sib tham kom
  • Pob: plywood Case
  • Qauv: SL833
  • Standards: AITM 2,0006, BSS 7322, DEB FEEM 25 COV LUS QHIA NTXIV F Part IV
  • khoom Nthuav dav

    khoom cim npe

    OSU Heat Release Rate Tester Stainless Steel Combustion Test Chamber Equipped

    Khoom ntaub ntawv  ntawm OSU hHeat Tso Rate Tester

    The OSU heat release rate tester approved by FAA of the Federal Aviation Administration of the United States was originally designed by Smith of Ohio State University in 1972, and later became a FAA designated combustion test instrument for testing the heat release rate of Aeronautical materials. The test standards are FAR Part 25 Appendix F Part IV, Airbus AITM 2.00. 06, Boeing BSS 7322.

    Performance yam ntxwv ntawm OSU Thaum tshav kub kub Tso Rate Tester

    1. Stainless steel combustion test chamber with high temperature glass observation window;
    2. The heat radiation source is 4 Glowbars heating rods, which can provide 35KW/M2 heat radiation flux.
    3. Two independent PID temperature controllers are used for heating temperature control.
    4. Equipped with fully automatic pneumatic sample propulsion device and shielding door device;
    5. Equipped with upper burner and movable lower burner;
    6. Rotor flowmeter can be used to adjust the gas flow rate of upper and lower burners.
    7. Equipped with movable T-type calibration burner device and flow controller;
    8. Mass flow controller is applied to thermopile temperature calibration automatically.
    9. Water-cooled heat flow meter is equipped with cooling mode to measure the heat radiation flux of the fire surface.
    10. The air temperature control device can provide constant temperature and flow air for the test chamber.
    11. The orifice flowmeter is used to measure the flow pressure entering the test bin.
    12. Equipped with data acquisition system and heat release standard test software.

    Khoom  tsis of OSU Heat Release Rate Tester

     loj  760mm (W) x 1850mm x (H) x 850mm (D)
     Nyhav  218KG
     Hluav taws xob uas yuav tsum tau  220 V, 35 Amps
     ambient kub  10 ℃ 35 ℃
     koom haum pab Gas  Qhov kub thiab tas Tam sim no Gas
     combustion roj  methane
     Standard   AITM 2,0006, BSS 7322, DEB FEEM 25 COV LUS QHIA NTXIV F Part IV
     daim ntawv sau npe  aviation ntaub ntawv

     


  • Yav dhau los:
  • Tom ntej:

  • Sau koj cov lus no thiab xa nws mus rau peb