SL-FL37 Automatic Ignitability Building Materials Flammability Tester
Laifọwọyi Ignitability Ilé elo Flammability ndán fun Ilé elo
Ọja ifihan ti Ilé elo Ignitability ndán
Ilé elo Ignitability ndán, lati mọ awọn ignitability ti ile awọn ọja tunmọ si taara impingement ti inaro
single-flame source in the principle of German Klein Brenner, For related categories B, C, D, e, Bfl, Cfl, Dfl and Efl in all combustible
materials testing, the device provide overall solution, and is applicable to the operator, the tester also meet the DIN 4102- 1; class B2 test requirements.
Ọja sile ti awọn Ilé elo Ignitability ndán
|
ibaramu otutu |
15 ° C ~ 25 ° C |
|
Relative humidity |
≤ 85% |
|
Supply voltage and power |
220V 50HZ 100W |
|
Gas source |
C ommercial propane with a purity of not less than 95%. The ordinary test can also be replaced by liquefied petroleum gas (The user needs to bring their own safety). |
|
Bunsen burner applies flame time |
15s |
|
Single-chip control |
D igital display |
|
The burner diameter |
Φ0.17mm |
|
T he Bunsen burner flame length |
20mm±2mm, and the burner can be tilted 45° |
|
Apply flame |
(1s-99 s) ±0.5s to the sample, which can be adjusted arbitrarily with an accuracy of ±0.2s |
|
Combustible gas source |
P ropane with a purity of more than 95% |
|
apa miran |
850 mm (W) X 450 mm (D) X 800 mm (H) |
|
àdánù |
24KG |
Ọja Ẹya ati elo ti awọn Ilé elo Ignitability ndán
1. O ti wa ni ergonomically apẹrẹ ati ṣiṣẹ. Gbogbo awọn igbeyewo ti wa ni pari nipa iboju ifọwọkan isẹ. Ìyí adaṣiṣẹ jẹ ga. Awọn esi ti tẹlẹ igbeyewo le wa ni fipamọ ati awọn ti tẹlẹ igbeyewo data le ka.
2. Awọn fifi motor lé awọn ayẹwo agbeko le dari lati laifọwọyi gbe;
3. Bunsen adiro le ti wa ni titunse ni ilosiwaju ati padasehin;
4.1.5mm alagbara, irin awo irú;
5.2 àìpẹ, irin ooru-sooro gilasi enu ė igun akiyesi igbeyewo, ė (pẹlu titiipa) rọrun ati ki o wulo
6. High-titẹ laifọwọyi iginisonu, ti o tọ ijona;
7. Awọn iginisonu orisun le ti wa ni laifọwọyi tilted nipa 45 iwọn;
8. Awọn ọwọ iná iga ti wa ni titunse nipa a konge regulating àtọwọdá;
9. The ayẹwo dimu le ṣee gbe si oke ati isalẹ ki o si pada ati siwaju;
10. Ipese pẹlu meji ayẹwo holders.
11. ina wiwọn kan asekale;
12. High ìyí ti adaṣiṣẹ, deede ati ki o rọrun lati ṣiṣẹ esiperimenta data;
13. Box iwọn: iwọn 835 × ijinle 400 × iga 815mm
14. Ohun elo ti: 1.5mm alagbara, irin
15. The isalẹ ti apoti ti wa ni a alapin adayeba soronipa, ati awọn soronipa wa ni kq ti a 5cm * 5cm square soronipa (a otitọ 1,5 mm nipọn irin soronipa, 50mm ga) lati pa awọn airflow nipasẹ.
16. osišiše, otito solderless ilana
17. Fọwọkan awọn àpapọ:
a. Iwọn: 7 inches munadoko àpapọ iwọn ipari 15.5cm iwọn 8.6cm;
b. O ga: 800 * 480
c. Communication ni wiwo RS232, 3.3V CMOS tabi TTL, ni tẹlentẹle ibudo mode
d. Ipamọ agbara: 1G
e. Lo funfun hardware FPGA iwakọ àpapọ, "odo" ibẹrẹ akoko, ṣiṣe awọn lori agbara
f. Lilo M3 + FPGA faaji, M3 jẹ lodidi fun ẹkọ Ìbòmọlẹ, FPGA fojusi lori TFT àpapọ, iyara ati dede ti wa ni asiwaju awọn kanna eni
g. Awọn ifilelẹ ti awọn oludari adopts-kekere agbara isise ati laifọwọyi ti nwọ awọn agbara pamọ-mode.
Ọja alaye ti the Ilé elo Ignitability ndán
1.Provide boṣewa alagbara, irin ayẹwo dimu ati jakejado alagbara, irin ayẹwo dimu;
2.The iginisonu orisun le wa ni gbe ni inaro tabi 45 iwọn, o dara fun isalẹ eti ati eti iginisonu;
3.The ina iga ti wa ni titunse nipa a konge abẹrẹ àtọwọdá;
4. Pipese a ọwọ iná iga idiwon ẹrọ ati a ayẹwo ijinna won won;
5.The ayẹwo dimu le ṣee gbe si oke ati isalẹ ki o si osi ati ọtun nipa darí eto.
awọn aṣayan wa
Multilayer apẹrẹ dimu
Loose yó apẹrẹ dimu
Anemometer 0-10 m / s ibiti o
ìlà ẹrọ pẹlu 0.2 sec ìpín
Ipa atehinwa àtọwọdá: Laarin 10 kPa ati 50 kPa
Standards:
DIN: DIN 53438
ISO: ISO 11925-2
EN: EN 13501
IEC: IEC 61730-2: 2016
Dimension: 850 mm (W) X 450 mm (D) X 800 mm (H)
iwuwo: 24kg
fifi sori awọn ibeere
Gaasi: propane pẹlu kan kere ti nw ti 95%.
What is the EN ISO 11925-2 testing?
EN ISO 11925-2:2002-Reaction to fire tests-Ignitability of building products subjected to direct impingement of flame-Part 2: Single-flame source test.
EN ISO 11925-2 Test time
There are 2 ignition times to choose from, 15s or 30s. The test start time is the start time of ignition.
If the ignition time is 15s, the total test time is 20s, calculated from the start of ignition.
If the ignition time is 30s, the total test time is 60s, calculated from the start of ignition.
